V-Lock Cord Retaining System

This V-Lock system by Schurter is an attractive and simple solution to prevent an unintentional unplugging. Various different connectors, Power Entry Modules and several country-specific power cables are available with this option.

.

The V-Lock locking system can be used for 10A and 16A power inlets and connectors according to IEC 60320. This system works in such a way that there is a pin in the socket, interlocking with a notch in the plug and thus prevents an unintentional pullout of the power cable. The advantage of this system is that there is no need for a specific socket system or retaining device that has to be adapted and built-in.

The locking is released by pressing on the releasing lever. This lever is easily detected by its bright yellow colour and thus distinguishes this system from existing power cable connections. The extraction force is a minimum of 200 N. Typical applications are in medical appliances,
analysis and laboratory instruments, Telecom and IT- devices, power distribution or radio and TV-studios.

.

USP's: - prevents unintentional disconnection
- increased safety and reliablility
- most cost effective cord retaining solution on market
- attractive design
- easy to use

The following connector types can be manufactured with the V-Lock option in series:
6010, 6061, GSP1, GSP2, DF11, 6600-3, 6600-4, 6610, 4797

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Click on the Link Below to View Catalogue

Walsall Electrical Equipment

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Finder has announced additions to its 18 Series of PIR motion detectors supporting a variety of interior energy saving schemes.  The compact 18.21 and 18.31 variants will meet the needs of higher ceiling, higher load switching applications and those requiring direct interface to a PLC or BMS.

Recess mounted, the flush fitting 18.31 suits suspended or plasterboard ceilings while the 18.21 is a low profile PIR for hard surface mounting.  Providing a 10 amp rated normally open volt free output, the detectors will switch loads at any voltage and are not restricted to 230VAC mains tasks.  24V ac/dc supply versions are also available for applications without a mains supply or where safe, low voltage operation is required.

With a 110º wide sensing angle and a reach of 2.8m, the 18.21-0300 and 18.31-0300 PIRs will handle all types of regular ceiling height applications.  For high bay or extended ceiling height duties, the 18.31-0031 PIR variant offers a much longer sensing range of up to 8m.

The Finder PIRs also offer an adjustable light threshold setting allowing operation to be varied according to ambient light conditions.  In addition, an enhanced light-on time adjustment of up to 35 minutes makes the PIRs well suited to HID lamp applications, which for reasons of preserving lamp life, place a restriction on the number of starts per hour.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Customizable Devices Provide High Sensitivity at Very Low Flows, Low Pressure Drop,
High Stability, and Help Reduce Production Costs

Honeywell announced the introduction of the Honeywell Zephyr™ Digital Airflow Sensors that deliver the industry’s most accurate airflow reading across the operating range of the sensor. The new HAF Series devices provide highly accurate digital output, enhanced reliability, and repeatable measurements to meet many medical and industrial application specifications.

The Honeywell Zephyr™ Digital Airflow Sensors offer several competitive advantages not found in other digital airflow sensors, including:

* High 2.5% accuracy that allows for very precise airflow measurement, often ideal for demanding applications with high accuracy requirements;

* Customization, which allows the sensor to be designed to meet specific end-user  needs;

* High sensitivity at very low flows to enable the detection of the presence or absence of airflow in the application;

* High stability to reduce errors due to thermal effects and null shift to provide accurate readings over time, often eliminating the need for system calibration after printed circuit board (PCB) mount, and periodically over time;

* Low pressure drop, which typically improves patient comfort in medical applications, and reduces noise and system wear in components such as motors and pumps;

* Linear output to provide a more intuitive sensor signal than the raw output of basic airflow sensors which can help customers reduce production costs and implementation time.

The Honeywell Zephyr™ Digital Airflow Sensors simplify the customer’s production requirements due to Application Specific Integrated Circuit (ASIC)-based I2C digital output that eases integration to micro-processors or microcontrollers, reducing PCB complexity and component count. Their small size occupies less space on the PCB, allowing for a smaller PCB, which can reduce production costs and simplify installation in space-restricted applications. Their low 3.3 Vdc voltage option and low power supply requirements allow for use in battery-powered and portable applications.

Honeywell Zephyr™ Digital Airflow Sensors are designed to measure mass flow of air and other non-corrosive gases. They are available in standard flow ranges, and are fully calibrated and temperature compensated. They provide a digital interface for reading airflow over the specified full scale flow span and temperature range, and their thermally isolated heater and temperature sensing elements help provide a fast response to air or gas flow.

Potential medical applications include anesthesia delivery machines, hospital diagnostics (spectrometry, gas chromatography), nebulizers, oxygen concentrators, patient monitoring systems (respiratory monitoring), sleep apnea machines, spirometers, ventilators, and ventricular assist devices. Potential industrial applications include air-to-fuel ratio, analytical instrumentation (spectrometry, chromatography), fuel cells, gas leak detection, gas meters, HVAC filters, meteorology equipment, and variable air volume (VAV) systems on HVAC systems.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

New feature makes further customization possible

Schurter proudly announces the addition of a colour anodized aluminium housing to the popular line of metal pushbutton switches. The red and green housings can be used to distinguish the start/stop switching functions.

The robust vandal proof switch has an IK07 protection class for high impact and IP67 ingress protection against water and dust. Its low profile flat front construction guards against side impact. The actuator is made of durable stainless steel.

The standard versions of the new MSM color housing are offered in 19 and 22mm mounting diameters with electrical rating of 5A @ 250 VAC. Additionally, custom lettering, other mounting diameters, and colours are available. Versions with switching current and voltage of 100 mA @ 30 VDC, or 10A @ 250 VAC are also available. A version with IP67 rated microswitch provides seal protection from the back. Terminals are quick-connect. Assembly includes pre-wiring of the contact module, which is then snapped onto the actuator housing. Typical applications include controller panels for automated machinery, construction machinery, industrial and medical equipment.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Finder has extended its relay range with versions designed to suit photovoltaic (PV) inverters, domestic appliances and other equipment needing reinforced insulation, high ambient temperature handling and full disconnection contacts.  The latest product introductions comprise the 45.31 16A rated mini PCB relay and 3 special variants of the 66 Series 30A rated power relays.

With an extended 3mm contact gap, the single pole NO 45.31 relay meets the requirements of the EN60730-1 standard for household use and is rated for operation at an ambient temperature up to 105ºC.  It has a high sensitivity 24V DC coil rated at 360mW.  In common with the 66 Series specials, the 45.31 has been designed with an 8mm clearance and creepage distance, ensuring safe separation of supply and output, and reinforced insulation between coil and contacts, meeting the requirements of EN60335-1 (VDE0700).

The 2 pole NO (DPST-NO) 66.22-x600, 66.22-x600S and 66.82-x600 30 amp power relays ensure a contact gap separation of 1.5mm, fully meeting the requirements of the VDE0126-1-1 standard for PV inverter applications.  In addition, the 600S variant provides a 5mm airgap between relay base and PCB for extra cooling particularly in systems where forced air cooling is employed as with many PV inverters.

For added flexibility, the 66 Series relays provide the options of PCB and flange mounting and Faston 250 terminations.  A 35mm rail mounting adaptor is also available.  A wide range of coil voltages is offered, spanning from 6V through to 125VDC.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

A growing requirement for DC switch disconnectors for solar photovoltaic (PV) power supply systems has motivated Kraus & Naimer to introduce a brand new range of disconnectors specifically designed for this particular DC application.

With rated operational currents from 16 amps to 64 amps and voltages from 450 to 800 using a utilization category of DC-22A, a solution for most isolator applications within the solar photovoltaic market can be found.

Available in a totally insulated enclosure with the option of a red/yellow or grey /black padlockable handle and with a degree of protection to IP 66/67 they can be installed in the most arduous of environments.

To complement this series a complete range of AC switch disconnectors is also available in totally insulated enclosures, this enables the contractor to obtain his switch disconnector requirements for the entire installation from one source.

A new up to date catalogue giving part numbers and technical details is available on request.
http://www.krausnaimer.co.uk/photovoltaic-disconectors

.

.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

The PSE EX piezo switch from SCHURTER has achieved approval according to ATEX class II 2 G Ex ib IIB T4. This approval enables the switch to be employed in explosive facilities above ground.

The protection class refers to the permissible application in areas where an explosive atmosphere can arise from a mix of air and gases, vapors or mists. The switch may be typically used in oil/gas production systems, in petrochemistry, as well as in paint and varnish mixing facilities. Preparations for extending the approval to include dust-Ex applications are underway. The standard design is available for a mounting diameter of 16mm with pin connections and various housing colors. Additional mounting diameters and connection designs are available
upon request.

The switches for Ex applications are labeled with the type of approval and an identification number. In accordance with the ATEX guidelines, an installation manual is included in the scope of delivery.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/

Bulgin announces new version of MPI range of illuminated vandal resistant switches.

All MPI switches have bodies and buttons machined from high-grade stainless steel. A tough Polycarbonate lens in the stainless steel actuator gives a robust and aesthetically-pleasing switch.

All switches are front-panel sealed to IP66. However, Bulgin’s new range is also rear-of-panel sealed. This makes them suitable for use outdoors or in other situations where condensation or leakage behind control panels can be problematic. Rear panel sealing is available in a variety of styles, including single and dual colour with dot or ring LED illumination. Independent switch and LED terminals allows customers the flexibility to choose between permanent or controlled illumination. Contacts are single-pole push-to-make.

“The MPI series of switches boast IP66 sealed properties combined with a rugged design and a variety of style options,” comments John Wilson, MD of Elektron Technology. “With this latest addition to the Bulgin range Elektron Technology further enhances its complete design-and-manufacture service, offering our customers across a number of industries a flexible, quality solution to meet their control panel design needs.”

The switches have either solder tags or screw terminals, which facilitates easy field servicing, and also feature potted moulding and flying leads to the rear of the switch. With integral supply resistors the LEDs can now be driven directly from 6, 12 and 24V supplies.

The MPI series is tested to 750,000 mechanical and 35,000 electrical operations and rated at 50mA, 24V dc. The series has also recently undergone design improvements at construction stage, incorporating surface mount LEDs and TVS’s.

All switches in the MPI series have momentary action contacts making them ideal for access control and door entry applications including lifts, panic buttons, car park barriers, emergency telephones, vending machines and food processing.

.

Enquiry Form: https://www.epreston.co.uk/contact/

Home Page: https://www.epreston.co.uk/epblog/